CITS Carpenter Previous Year Question Paper
CITS Carpenter Previous Year Question Paper
CITS की परीक्षा के लिए Carpenter से संबंधित काफी महत्वपूर्ण प्रश्न पूछे जाते हैं इसीलिए CITS परीक्षा की तैयारी करने वाले सभी उम्मीदवारों को Carpenter से संबंधित जानकारी होना बहुत ही जरूरी है. CITS की तैयारी करने के लिए हमारी वेबसाइट पर आपको ऑनलाइन फ्री टेस्ट दिए जाएंगे और इस परीक्षा के कुछ महत्वपूर्ण नोट्स प्रश्न उत्तर के रूप में दिए जाएंगे आज के इस पोस्ट में भी आपको CITS से संबंधित काफी महत्वपूर्ण प्रश्न और उनके उत्तर नीचे दिए गए हैं जो कि पहले परीक्षाओं में पूछे जा चुके हैं लेकिन यहां पर हमने सभी प्रशन एक लाइन में दिए हैं ताकि है आपको आसानी से याद हो सके.
Q 1) The first formed round dark portion of the tree is called ……………..
A) Ring
B) Pith
C) Bark
D) Cortex
Q 2) Which of the following can resist attack by white ants?
A) Deodar
B) Teak
C) Chir
D) Kail
Q 3) Which saw would be best choice for cutting an opening in wallboard for a switch box?
A) Key hole saw
B) Coping saw
C) Hacksaw
D) Back saw
Q 4) Name the part of the band saw machine which is provided between the wheels to support the work piece. /
A) Table
B) Arm
C) Guide post
D) Column
Q 5) When a tree grows, many of its branches fall and the stump of these branches in the trunk is covered. In the
sawn pieces of timber the stump of fallen branches appear as ……………
A) Spot
B) Knot
C) Ridge
D) Wedge
Q 6) In the figure given below, which one is dovetail joint?
A) Joint A
B) Joint B
C) Joint C
D) Joint D
Q 7) Identify what is shown in figure given below.
A) Pins
B) Ribs
C) Dowels
D) Keys
Q 8) Which of these joints is so weak that it has to be reinforced with steel plates or brackets when building roof
trusses?
A) Dovetail joint
B) Bridle joint
C) Butt joint
D) Mortise and tenon joint
Q 9) The distance from a given point on one thread to the corresponding point on the next thread is called ……….. /
A) Helix
B) Lead
C) Pitch
D) Flat
Q 10) Which type of lock is NOT permanently attached to the door?
A) Pad lock
B) Knob lock
C) Deadbolt
D) Camlock
Q 11) A clicking noise on a band saw indicates ….
A) A broken wheel guard
B) A crack in the blade
C) Electrical power tripping
D) Nothing wrong
Q 12) What is the type of hinge shown in figure given below?
A) Butt hinge
B) Lift off hinge
C) Flush hinge
D) Security butt hinge
Q 13) The size of a tablesaw is determined by the ………….
A) Height of the table
B) Shaft diameter
C) Blade diameter
D) Blade width
Q 14) The box shown in figure given below is called …………….
A) Carpenter s box
B) Shaping box
C) Slitting box
D) Mitre box
Q 15) The tool used to test squareness of wood is ……………..
A) Ruler
B) Framing square
C) Try square
D) Combination square
Q 16) What is used to extract nails?
A) Ball pein hammer
B) Claw hammer
C) Mallet
D) Sledge hammer
Q 17) Figure below shows a piece of wood held in a vice. When using a plane, which direction should it move? /
A) From left to right
B) From right to left
C) In any direction
D) Direction of movement is not important
Q 18) Which tool is used to make a fine cut in wooden workpiece?
A) Hand saw
B) Wooden saw
C) Tenon saw
D) Rip saw
Q 19) Which statement is NOT true with respect to the tool shown in figure below?
A) It is called brace
B) It is used with auger bits
C) It is used for drilling small diameter holes
D) It allows a lot of force to be applied to the drill bit
Q 20) Freshly cut lumber that has not been dried is called …………….
A) Raw lumber
B) Fresh lumber
C) Green lumber
D) Base lumber
Q 21) The marks put on boards or pieces to keep them in order during gluing, joining and assembly, are called
……….
A) Assembly marks
B) Witness marks
C) Visible marks
D) Limiting marks
Q 22) The post (figure given below) at the top or bottom of a stairway that supports the handrail, is called ……….. /
A) Newel
B) Muntin
C) Ogee
D) Mould
Q 23) The angle at which the leading edge of the teeth are cut on a saw blade, is called
A) Face
B) Rake
C) Cutting angle
D) Clearance angle
Q 24) The kind of door used in fire exits is ……………
A) Double action door
B) Panel door with panic bar
C) Panel door
D) Revolving door
Q 25) The disadvantage of sliding door is ……………. of cabinet opening is available.
A) One-half
B) One-third
C) One-fourth
D) One-fifth
Q 26) The upper most member of a door frame is called …………….
A) Door head
B) Door roller
C) Door closer
D) Door jamb
Q 27) The member which is placed horizontally to support common rafter of a sloping roof, is ……………..
A) Purlin
B) Cleat
C) Batten
D) Strut
Q 28) Which of these is NOT a type of truss?
A) King post truss
B) Queen post truss
C) Prince post truss
D) Pratt truss
Q 29) The outer protective layer of a tree is called …………….
A) Bark
B) Bast
C) Cambium
D) Sap wood
Q 30) The ratio of rise to span of a truss is called …………….
A) Scale
B) Lead
C) Peak
D) Pitch
Q 31) A tool similar to an axe with the blade perpendicular to the handle, used to carve wood, is called ….
A) Awl
B) Adze
C) Scraper
D) Gouge
Q 32) When you use a chisel, it is important that you ………
A) Keep both hands behind all the times
B) Hit harder if chisel is blunt
C) Chisel across the grains if possible
D) Use the biggest possible chisel at all the times
Q 33) Which tool can produce mouldings, trim edges, form recesses and cut grooves?
A) Jack plane
B) Belt sander
C) Reciprocating saw
D) Router
Q 34) A jointer is a tool designed to …………….
A) Cut mitres
B) Apply glue
C) Plane surfaces
D) Rip narrow stock
Q 35) It is a knife which has blade between two handles. The handles are at right angles to the blade. It is used to
smooth a surface by pulling the blade over the stock. Name the tool.
A) Pullknife
B) Drawknife
C) Right angle knife
D) Bridge knife
Q 36) A hxagonal wrench is also known as …………..
A) Allen wrench
B) Stillson wrench
C) Socket wrench
D) Ratchet wrench
Q 37) Figure given below shows two types of …………………
हœ ।
A) Casters
B) Cambers
C) Rollers
D) Drag wheels
Q 38) The preferable way to cut the ends of a number of boards at the same angle is to use ………
A) Mitre box
B) Protractor
C) Combination square
D) Combination bevel
Q 39) You have a short section of lumber which you want to round off. Name the suitable file for this work.
A) Single cut
B) Double cut
C) Curved cut
D) Rasp cut
Q 40) Black sandpaper used to smooth metal and take off rust is ………..
A) Emery
B) Aluminium oxide
C) Silicon carbide
D) Pumice
Answer
| Question No. |
Option |
| 1 | B |
| 2 | B |
| 3 | A |
| 4 | A |
| 5 | B |
| 6 | D |
| 7 | C |
| 8 | C |
| 9 | C |
| 10 | A |
| 11 | B |
| 12 | B |
| 13 | C |
| 14 | D |
| 15 | C |
| 16 | B |
| 17 | A |
| 18 | C |
| 19 | C |
| 20 | C |
| 21 | B |
| 22 | A |
| 23 | B |
| 24 | B |
| 25 | A |
| 26 | A |
| 27 | A |
| 28 | C |
| 29 | A |
| 30 | D |
| 31 | B |
| 32 | A |
| 33 | D |
| 34 | C |
| 35 | B |
| 36 | A |
| 37 | A |
| 38 | A |
| 39 | D |
| 40 | A |
CITS परीक्षाओं की तैयारी करने वाले सभी उम्मीदवारों के लिए इस पोस्ट में Cti entrance exam model paper Carpenter pdf in hindi, Cti entrance exam model paper Carpenter pdf, Cti entrance exam book pdf in hindi, Cti previous year question paper Carpenter, Cits Carpenter previous year question paper pdf, से संबंधित काफी महत्वपूर्ण जानकारी दी गई है यह जानकारी फायदेमंद लगे तो अपने दोस्तों के साथ शेयर करें और इसके बारे में आप कुछ जानना यह पूछना चाहते हैं तो नीचे कमेंट करके अवश्य पूछे.