CITS Entrance Exam FITTER Previous Year Questions
CITS Entrance Exam FITTER Previous Year Questions
CITS की परीक्षा के लिए Fitter से संबंधित काफी महत्वपूर्ण प्रश्न पूछे जाते हैं इसीलिए CITS परीक्षा की तैयारी करने वाले सभी उम्मीदवारों को Fitter से संबंधित जानकारी होना बहुत ही जरूरी है. CITS की तैयारी करने के लिए हमारी वेबसाइट पर आपको ऑनलाइन फ्री टेस्ट दिए जाएंगे और इस परीक्षा के कुछ महत्वपूर्ण नोट्स प्रश्न उत्तर के रूप में दिए जाएंगे आज के इस पोस्ट में भी आपको CITS से संबंधित काफी महत्वपूर्ण प्रश्न और उनके उत्तर नीचे दिए गए हैं जो कि पहले परीक्षाओं में पूछे जा चुके हैं लेकिन यहां पर हमने सभी प्रशन एक लाइन में दिए हैं ताकि है आपको आसानी से याद हो सके.
Q 1. In outside micrometer, datum line and graduations are marked on ….
A) Spindle
B) Barrel
C) Frame
D) Anvil
Q 2. The two parts of a try square are ……………..
A) Straight and blade
B) Stick and plate
C) Stock and blade
D) Stock and wedge
Q 3. A micrometer has a negative error of 0.03 mm. What is the correct reading if the
micrometer measures 40.53 mm?
A) 40.50 mm
B) 40.56 mm
C) 40.46 mm
D) 40.59 mm
Q 4. Kerosene oil is used as a coolant, while drilling a workpiece made of ………..
A) Brass
B) Bronze
C) Aluminium
D) Wrought iron
Q 5. Which one of these bonds is most commonly used on grinding wheels?
A) Vitrified
B) Rubber
C) Shellac
D) Silicate
Q 6. In the figure given below, which one is cross peen hammer?
A) A
B) B
C) C
D) D
Q 7. For general purpose, a bench vice is fixed at a height of …………..
A) 80 cm
B) 90 cm
C) 106 cm
D) 125 cm
Q 8. Identify the machine shown in figure given below.
A) Planer
B) Slotter
C) Shaper
D) Milling machine
Q 9. The bed of a lathe is made of ……………….
A) Alloy steel
B) Mild steel
C) Cast iron
D) Wrought iron
Q 10. Which of these is NOT a part of centre lathe?
B) Feed rod
C) Arbor
D) Lead screw
Q 11. In the figure given below, identify the lathe operation being done.
A) Knurling
B) Indenting
C) Scratching
D) Pattern making
Q 12. Which among these metals is the lightest?
A) Tin
B) Lead
C) Aluminium
D) Copper
Q 13. Identify the gauge shown in figure given below.
A) Standard gauge
B) Wire gauge
C) Depth gauge
D) Drill gauge
Q 14. Which of these is an example of semi-liquid lubricant?
A) Graphite
B) Grease
C) Lard oil
D) Castor oil
Q 15. The most common cutting fluid used in almost all machining operations is ….
A) Soluble oil
B) Water
C) Compressed air
D) Kerosene
Q 16. Which of these cutting tools is used to finish and enlarge a hole?
A) Die
B) Tap
C) Reamer
D) Boring bar
Q 17. The process of bevelling the end of an existing drilled hole is called …..
A) Boring
B) Spot-facing
C) Counter-boring
D) Counter-sinking
Q 18. Figure given below shows a type of cut of a file. What is it?
A) Single cut
B) Double cut
C) Curved cut
D) Rasp cut
Q 19. The teeth of the hacksaw blade are bent as shown below. It is called ……
A) Pattern
B) Style
C) Set
D) Series
Q 20. It is a type of paper that can be used for sanding down hard and rough surfaces. It is
called ………
A) Rigid paper
B) Tough paper
C) Hard paper
D) Emery paper
Q 21. Figure below shows spark characteristics of four different alloy steels. Which one
represents high carbon steel?
A) A
B) B
C) C
D) D
Q 22. Which one of these is NOT a type of oxy-acetylene flame?
A) Neutral flame
B) Natural flame
C) Oxidising flame
D) Carburizing flame
Q 23. The drilled hole is larger than the size of the drill used. It could be due to ……
A) Too much feed
B) Helix angle not accurate
C) Lip clearance not accurate
D) Unequal length of the cutting edges
Q 24. If a bench vice is over-tightened, what is likely to be damaged?
?
A) Handle
B) Spindle
C) Square nut
D) Fixed jaw
Q 25. Which of these is not a base unit under SI system of units?
A) Kelvin
B) Candela
C) Mole
D) Joule
Q 26. The main purpose of heat treatment process “normalizing” is ………
A) Remove induced stresses
B) Improve machinability
C) Soften steel
D) Increase toughness and reduce brittleness
Q 27. The heat treatment process “annealing” is done to
A) Increase toughness
B) Increase softness
C) Increase hardness
D) Increase brittleness
Q 28. What is the type of filing being done as shown in figure given below?
A) Straight filing
B) Plane filing
C) Draw filing
D) Finish filing
Q 29. V block is used to hold round bars. It has a Vee groove, which is usually …
A) 30 degrees
B) 60 degrees
C) 90 degrees
D) 120 degrees
Q 30. Figure below shows a tool marked ‘A’, which removes taper shank drill from the nose
of the machine spindle. It is called …..
A) Wedge
B) Drift
C) Lever
D) Flat
Q 31. What should be used to check leakage before using oxy-acetylene welding
equipment?
A) Soap water
B) Salt water
C) Fresh water
D) Hard water
Q 32. Which caliper is used to measure width of a slot?
A) Outside caliper
B) Inside caliper
C) Jenny caliper
D) Odd leg caliper
Q 33. Which of these is an example of shrinkage fit?
A) Cart rim on wooden rim
B) Tyre on rail wheel
C) Tyre on bicycle rim
D) Flywheel on the shaf
Q 34. Which of these is a correct statement?
A) A clearance fit always provides interference
B) An interference fit always provides clearance
C) An interference fit may sometimes provide clearance and sometimes interference
D) A transition fit may sometimes provide clearance and sometimes interference
Q 35. In a riveted joint, the plates are placed end-to-end and jointed through cover plates.
This joint is called ….
A) Lap joint
B) Butt joint
C) Edge joint
D) Corner joint
Q 36. A gauge is basically a ……………
A) Measuring instrument
B) Checking instrument
C) Rectifying instrument
D) Installation instrument
Q 37. Which of these sheets is the thinnest?
A) 10 gauge sheet
B) 20 gauge sheet
C) 30 gauge sheet
D) 40 gauge sheet
Q 38. As per Indian Standards a special set of slip gauges is used consisting of …
A) 81 pieces
B) 112 pieces
C) 120 pieces
D) 130 pieces
Q 39. As shown in figure below, what is being used to check spark plug gap?
A) Snap gauge
B) Feeler gauge
C) Leaf gauge
D) Limit gauge
Q 40. What is the type of thread shown below?
A) Buttress thread
B) Knuckle thread
C) Acme thread
D) Brown and Sharpe worm thread
Answer
| 1 | B | 21 | A |
| 2 | C | 22 | B |
| 3 | B | 23 | D |
| 4 | C | 24 | B |
| 5 | A | 25 | D |
| 6 | C | 26 | A |
| 7 | C | 27 | B |
| 8 | B | 28 | C |
| 9 | C | 29 | C |
| 10 | C | 30 | B |
| 11 | A | 31 | A |
| 12 | C | 32 | B |
| 13 | B | 33 | A |
| 14 | B | 34 | D |
| 15 | A | 35 | B |
| 16 | C | 36 | B |
| 17 | D | 37 | D |
| 18 | D | 38 | B |
| 19 | C | 39 | B |
| 20 | D | 40 | A |
CITS परीक्षाओं की तैयारी करने वाले सभी उम्मीदवारों के लिए इस पोस्ट में cti entrance exam model paper FITTER pdf in hindi cti entrance exam model paper FITTER pdf cti entrance exam book pdf in hindi cti previous year question paper FITTER cits FITTER previous year question paper pdf cits FITTER previous year question paper cti FITTER question paper cti entrance exam model paper fitter pdf से संबंधित काफी महत्वपूर्ण जानकारी दी गई है यह जानकारी फायदेमंद लगे तो अपने दोस्तों के साथ शेयर करें और इसके बारे में आप कुछ जानना यह पूछना चाहते हैं तो नीचे कमेंट करके अवश्य पूछे.